![]() ![]() ![]() I wish instructions were more clear on the included manual. I was sure to use the name and model number on this thread, to make search-friendly. Thanks everyone! I hope that this post helps future buyers clear up any confusion regarding the 90 degree default dwell reading on the timing light. Overall, I think it was worth the $100 that I spent on it on Amazon. The RPM feature(also common with other timing lights) will come in handy when adjusting the mixture screws to get the "fastest idle". So far, I like the easy to read blue backlight display. The one i have is the one that Dave described as "fancier one that also measures voltage and dwell"(Thanks for finding the post, Dixon). It starts at 90 degrees, but should drop to around 50 with engine running. ![]() It turns out that it's the latter- just informational. 8 Images about Innova Timing Light 3568 Manual - locatorever : Equus 5568 - INNOVA Pro Digital Timing Light (DIS) User Manual Page, Digital Image Pro User Manual - digital imaging and also Equus 5568 - INNOVA Pro Digital Timing Light (DIS) User Manual Page. Or, if it just served as read-only (informational only) display. Innova Timing Light 3568 Manual - locatorever. I didn't know whether I needed to adjust the timing light to 50 degrees dwell to match the distributor dwell, and in order for it to properly time the engine. I was just a little confused at first regarding the dwell reading on the timing light, since it defaulted to 90 degrees when I hooked it up. LCD display is backlit in soft blue light for easy viewing in low-light areas.Thanks, Mike! Yes, I got it from here. Displayed information depends on operating mode selected. LCD Display - Provides a digital display of engine operating parameters including engine speed (rpm), advance (degrees), dwell angle (degrees), and battery and charging system voltage. Flash Switch - Push to turn strobe light on. ■ Green DWELL Clip - Connects to the negative (tach) side of the ignition coil.Ĭontrol Panel Controls and Indicators (see Figure 2)ġ. ■ Inductive Pickup Clip - Clamps around No. ■ Black Battery Clip - Connects to battery negative (-) terminal or bare metal chassis ground. ■ Red Battery Clip - Connects to battery positive (+) terminal. Inductive Pickup Leads - Detachable leads assembly connects timing light to the battery and ignition system: Control Panel - Contains the controls and indicators necessary to operate the timing light.Ĥ. Rotates over approximately 90° to allow for easy illumination of timing marks in hard to reach locations.ģ. Swiveling Head - Contains the xenon bulb. Xenon Bulb - Used to illuminate timing marks for checking timing.Ģ. Operating Controls and Indicators - General (see Figure 1)įigure 1. The timing light may also be used on vehicles equipped with DIS (distributorless ignition systems). This timing light is designed for use with all 12-volt negative-ground vehicles. Please contact these manufacturers for instructions on how to use an inductive pickup with their systems. ■ Some aftermarket ignition systems and/or specialty spark plug wires (solid core wires, racing wires, off-road wires) radiate above normal ElectroMagnetic Interference (EMI) and Radio Frequency Interference (RFI) which can cause improper operation of testing equipment. ■ If the Digital Timing Light readout becomes inoperative or locks up during use, disconnect and reconnect the timing light's positive battery clip from the battery to reset the unit. OBSERVE ALL SAFETY PRECAUTIONS.ĮMI/RFI problems with Digital Timing Lights: Turn off ignition before connecting (or disconnecting) any testing equipment.ĪLWAYS READ THE VEHICLE'S SERVICE MANUAL BEFORE PERFORMING ANY PROCEDURE. DO NOT smoke or allow spark or flame near the battery.īE CAREFUL when working near high-voltage parts (spark plugs or coil terminals). The vehicle battery produces explosive gases. In this video I mistakenly refer to the crank pulley as the cam pulley - please excuse the. TIMING LIGHT, THESE PARTS MAY APPEAR TO BE STOPPED OR MOVING SLOWLY. The recommended setting is 14-16 degrees BTDC by the company that refurbished my Lucas distributor. Put blocks on drive wheels.Īvoid moving fan blades or any potentially moving parts. Put transmission in “park” (for automatic) or “neutral” (for manual). Only work on a vehicle in a well-ventilated area. Īlways observe safety precautions whenever working on a vehicle.ĭO NOT wear loose clothing, watches, rings or other jewelry when working on a vehicle. VOLTMETER OPERATION.ĬHECKING DWELL ANGLE. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |